有點危險，一般不建議這樣用，雖然沒有脈沖功能的充電器，理論是可以給鋰電池充電的，但是依然可能會傷害鋰電池，雖然鋰電池有保護板，理論過充或者過放時候能起到保護作用，如果充電時經常觸發過充保護電壓，那這個充電器的輸出電壓設置就不正確。發生這樣的現象后，那落后的電池永遠落后。有保護板也盡量不要高。因為電池在電池盒里使用，平時是看不到電池的一致性狀態的，不知什么時候，萬一它的一致性出問題了，這時電壓又高了幾V。那電池就要倒大霉了，請關注：容濟點火器

實際上，鉛酸電池充電器為了克服鉛酸的大內阻,在恒流充電時把充電電壓提高了5%左右,也就是說就是你選用了一樣電壓充電器，給鋰電池供電時候，電壓會高出來一點的，因為鉛酸的內阻大，恒流充電為了達到效率都是在恒流時把恒壓電壓升高，這樣對鋰電池是很不利的。

主要是鉛酸電池充電過程中有二個電壓點會析氫和析氧，析氧電壓點為13.8V，析氫電壓點為14.7V，所以鉛酸充電器的高恒壓定在14.7V*塊數；低恒壓（浮充電壓）定在13.8V*塊數。

鋰電池保護板的保護電壓點如果是4.2V,那放心使用,無非就不要恒壓而已充電,但普通的保護板啟動電壓時4.25V,加上+/-0.035V的誤差,不是很安全吧? 18650可能沒多大事,鋁殼大單體難說了，很多鋰電池使用的是正常普通的保護板,保護板截止保護電壓4.25V ，所以這個保護在關鍵時候可能會起不到作用。

鋰電池內阻小，比如13串鋰電池也就是48伏，截止電壓要控制在54.6伏因為，而鉛酸電池恒流截止電壓是57.9伏，高出幾伏了。

當然，鉛酸電池如果改進一下是可以給鋰電池充電的，比如去掉低恒壓階段電路和脈沖電路，是可以用的。如果你如果觀察鋰電的充電曲線，可以發現在恒流階段充入約為96%的總容量；恒壓減流階段只充入4%的容量，如果轉燈就拔時，那鋰電已經充入了99.5%的容量了。所以鉛酸充電器充鋰電，也就是少了最后的均衡和浮充那0.5%的電量而已。將鉛充的高低恒壓都低調點，就都可以給鋰電充電了，只不過充不滿而已。不過鋰電又不會硫化，充不滿就充不滿吧，又不影響使用，壽命還會延長呀。

還有一個方法，打開外殼，把三極管C極串聯那個電阻阻值提升10倍,恒流只提升0.5%電壓,再調節下恒壓點,盡量做到每一個電池電壓均衡到4.18V左右為好。